
| If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
| Home | Register | FAQ | Donate | Members List | Calendar | vBGarage | Gallery | Search | Today's Posts | Mark Forums Read |
|
||||||

![]() |
|
|
Thread Tools | Search this Thread | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
|
XMR problems
I have an AIR FAULT scrolling message after I turn my bike on and drive around for 2 minutes and also my rear shocks are loosing stiffness. I checked for water in the lines because I was driving in the river but did NOT swamp the bike as the air intake for the air compressor is in the air box. I pulled the electrical connections and the only one that is dielectric greased is the rectifier plug with the yellow air line going to it. What can I check for and I was not doing anything that could have caused a shock(air bag) to burst.
__________________
2012 Outlander XMR, Dual LTE's, Custom 2" snorkel, Increased Rad angle, PC5 w/custom tune, 2.5" Rox handlebar riser, CVtech Primary w/650 helix, 1.5" Rubberdown SpringSpacers 2008 Grizzly 700, Two Brothers Slip on, Custom 2" Snorkel, 5" Rox riser, Pro Taper bars, Ricochet Skids, EPI clutch spring, and some L.E. engine parts |
|
#2
|
||||
|
||||
|
Not a good week for us lol
__________________
lil 08 Outty 650 Camo custom 2"snorkels, hmf slip on , 27" Mudlites,dual mirrors.plow bracket.windshield.hand warmers thumbwarmers.brp trunk 29.5 s/w laws ![]() ![]() |
|
#3
|
||||
|
||||
|
yeah certainly not a can-am week. As long as its all good in two weeks. I have figured out how to get rid of the air ride though. I looked on the can-am forums and it tells how to get rid of the check air suspension but not the air fault but it does say that the air fault message is a serious problem so thats gay
__________________
2012 Outlander XMR, Dual LTE's, Custom 2" snorkel, Increased Rad angle, PC5 w/custom tune, 2.5" Rox handlebar riser, CVtech Primary w/650 helix, 1.5" Rubberdown SpringSpacers 2008 Grizzly 700, Two Brothers Slip on, Custom 2" Snorkel, 5" Rox riser, Pro Taper bars, Ricochet Skids, EPI clutch spring, and some L.E. engine parts |
|
#4
|
||||
|
||||
|
Take it in for warranty, I had problems with my air ride as well. It's been good so far. I just can't remember what they changed. Good luck.
__________________
ALL STOCK (not anymore) |
|
#5
|
||||
|
||||
|
I'm going to our friends action power tomorrow. I have to get a boot for my rear axle, hopefully they have that part in stock. Come with me, we pi$$ them off together!!
__________________
![]() |
|
#6
|
||||
|
||||
|
So I fixed the problem as it was an air leak on the quick connect fittings. I took every quick connect fitting out and replaced them with a nut and furro fitting. Suspension is rock solid again and it only cost me $20 to buy the fittings. I would rather pay $20 then have to strip the snorkels to take it in for warranty work.
__________________
2012 Outlander XMR, Dual LTE's, Custom 2" snorkel, Increased Rad angle, PC5 w/custom tune, 2.5" Rox handlebar riser, CVtech Primary w/650 helix, 1.5" Rubberdown SpringSpacers 2008 Grizzly 700, Two Brothers Slip on, Custom 2" Snorkel, 5" Rox riser, Pro Taper bars, Ricochet Skids, EPI clutch spring, and some L.E. engine parts |
![]() |
| Tags |
| problems |
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | Search this Thread |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| can am xmr | ed_rexx | Buying an ATV | 15 | 07-30-2012 09:48 PM |
| Xmr | Ilovetoys | Can-Am ATV | 0 | 04-18-2012 06:30 AM |
| Can-am XMR | 06grizzly | TrackShare Lounge | 12 | 09-16-2011 08:16 PM |
| Can Am XMR CVT exhaust snorkel parts and XMR gauge pod | 2qwik2c | Classifieds | 1 | 06-05-2011 12:58 PM |
| Can Am XMR tires | AnolaBob | Can-Am ATV | 19 | 03-07-2011 03:53 PM |